Concrete Cutting in Agoura Hills CA - Clean Openings, Checked Before the Saw Starts
Need a doorway or window cut through concrete? We check what's inside first, then cut it clean with the dust planned for.
- Licensed and fully insured.
- Free estimates at your property.
- We reply within 1 business day.
Can someone cut a doorway or opening in my concrete safely?
Concrete cutting in Agoura Hills opens up concrete that's already in place, such as a doorway or window through a wall, an opening in a slab, a relief or separation cut, or a clean edge where new concrete ties into old. We're licensed and fully insured, based in Agoura Hills, and we work in the cities around it on both sides of the county line.
Most people who call about cutting are in the middle of something bigger, like a garage turning into a room, a pipe that has to run under a slab, or a cracked section of driveway coming out. The price mostly moves with how thick the concrete is, how long the cut runs, how much steel is inside and whether it needs a scan before we start, and the schedule usually turns on getting that scan and any drawings in hand. I write all of it down at the estimate, so you see your own number before anything gets cut.
How we do concrete cutting, start to finish
I start by finding out what's inside the concrete, using any drawings you have and a scan, because hitting a cable or a bar is no small mistake. That matters most in a post-tensioned slab, one with steel cables stretched tight inside it, since those cables carry stored force and cutting one can damage the structure or release that tension near whoever is standing there. Once we know where the steel is, we mark the cut, pick the saw that fits where it sits, and agree with you on how we'll handle the dust and where the slurry goes, the gray water and concrete paste a wet saw leaves behind. Then we cut, pull the pieces out and clean up before we leave.
A cut is often the first step of a bigger job. If a cracked or sunken section is coming out, we can saw a straight edge and pour the new section as part of concrete driveway building, and the same goes for widening or tying into an old slab with concrete patio construction. New concrete meets a sawn edge far better than a broken one.
Wall sawing for doors and windows
A wall saw runs on rails mounted to the concrete, so it makes square, accurate cuts for a new doorway or window. It suits garage and basement walls, where the opening has to come out straight and true.
Floor sawing for slabs and driveways
A floor saw is a walk-behind machine that cuts down through slabs and pavement. It's the one we bring when a driveway or patio section is coming out, or when a slab needs a relief or separation cut.
Core drilling for round holes
Core drilling bores a round hole for a pipe, drain or vent. It's also used at the corners of a square opening before the sawing starts, so the corners come out clean.
If a plumber or framer is waiting on your opening, call (747) 219-1796 instead of waiting on email, so we can get out and look at the site sooner.
What happens when you call us about concrete cutting in Agoura Hills?
Here's how a cutting job runs with us, from your first call to the walk-through. I'm the one you talk to, the one who writes your estimate, and the one on site with our crew.
Call or send the form
You call (747) 219-1796 or send a message saying where the cut goes, and we set a time for me to come out. I look at every job myself.
I look at the concrete
I check the wall or slab, ask what you need opened up and go over any drawings or post-tensioning records you have. Your written estimate spells out the prep, the steel we expect, the dust and slurry plan, and whether the job needs a permit, an engineer or a scan first.
We line up the scan and paperwork
I check with the building office for your address, and if your cut needs a permit, we apply for it before any work begins. The scan comes before the saw, because nobody cuts until we know what's inside.
We cut, clean up and walk it
I'm on site with our crew from layout to cleanup, and we cut the way we planned it with you. Before we pack up, we walk the opening with you and make sure the slurry and dust are dealt with.
Get a written estimate for your concrete cut
We reply within one business day to set a time, then I come out and leave you a free written estimate with no pressure to book. Send photos of the wall or slab and any drawings you have.
(747) 219-1796Concrete cutting in Agoura Hills and California's dust rule
Our crew cuts under a California safety rule that requires a dust reduction system whenever powered tools cut, grind, core or drill concrete or masonry, and that system has to actually bring down the dust in the air. That dust is a real hazard. Cal/OSHA calls the fine silica dust from concrete a known carcinogen and says it can cause silicosis, an incurable and often fatal lung disease, as well as lung cancer. So dust control isn't something we figure out once the saw is running. We plan it with you before the first cut, and more carefully when the work is inside the house or next to an open window.
A lot of the cuts we see here are in garage walls, driveways and patios, and on a sloped lot the slurry wants to run downhill toward the street, so we decide where it goes before we start. We plan cuts the same way on jobs in Calabasas and Westlake Village.
Concrete cutting questions from Agoura Hills homeowners
What openings can concrete cutting make in a house or slab?
Concrete cutting can make door and window openings in walls, openings in slabs and ceilings, relief cuts, separation cuts and clean tie-ins where new concrete joins old. It lets you open up concrete that's already in place, or connect a new part to it, without tearing the whole thing out.
Does my slab need a scan before cutting in Agoura Hills?
In most cases, yes, because drawings and what you can see on the surface help but don't prove the cut line is clear. One scanning firm advises going over the latest structural drawings and any post-tensioning records, then having the slab professionally scanned before any drilling, coring or cutting. Where steel is packed tight, one cutting company says X-ray imaging works best, but it needs access to both sides of the slab, everyone cleared out of the area and longer processing, so leave room for it in your schedule.
How do I keep concrete dust down when cutting near my house?
Ask for your job to be cut wet if water is available, because wet cutting holds the dust down and keeps the blade cool. Dry cutting is for spots where water is limited, and it needs stronger dust control to meet the state rule above. For a cut indoors, also ask which saw the crew plans to use, since one trade group's sample specification says gas-powered hand saws are normally kept to outdoor jobs because of their exhaust.
Which California license covers concrete sawing and coring?
The state's contractor licensing board lists concrete sawing, breaking and coring under its concrete related services class. Ask anyone you're thinking of hiring which license they carry before they bring a saw to your house.
How much does concrete cutting cost in Agoura Hills?
I can't give you a fair number until I've seen the concrete, so your price comes in a written estimate after I look at the site. Beyond the thickness, length and steel, things like an indoor cut that needs more dust containment, a tight spot the saw can barely reach, or breaking out and hauling off the cut pieces all add to it. An outdoor cut with easy access usually keeps it lower.
How do I get ready for a concrete cutting estimate?
Know where you want the cut, take a few photos of the wall or slab, and pull out any structural drawings or post-tensioning records you can find. It also helps to settle early who supplies water and power for the saw and who collects the slurry, since one trade group's sample specification has the owner providing water and electricity.
Concrete work that often follows a cut
When cracked or sunken panels come out, a new driveway poured on a dug-out, packed base gives you a slab that sits flat where the old one settled.
If you're widening a patio or swapping out a worn section, new concrete can be poured right against the sawn edge so the two meet cleanly.
Get your concrete cut planned right
We pick up weekdays from 6 AM to 9 PM and weekends from 8 AM to 10 PM, so call (747) 219-1796 after work or send the form whenever it suits you.